SVE Automotive Paints

Automobile Paints and coating

Shree Vandana is one of the leading companies in India which deals in wide range of automotive coating products. Adequate Technologies are used for various products in order to provide best quality products. They have a wide range of application such as -

Areas of Application
  • Cars and luxury vehicle coating- Refinish
  • Commercial and utility vehicle coating
  • Bus Body Paints
  • Two-wheeler coating
  • Railway Coating
  • Engine & spares coating
Sr. Areas Application Surface Preparation 1st Coat 2nd Coat Final Coat
1 Car Coating Rust/Paint Remover & Sanding Stoving or epoxy primer SVE PU Auto Paint SVE PU Clear
2 Refinish Car Coating Rust/Paint Remover & Sanding Epoxy primer, PU Primer SVE PU Auto Paint SVE PU Auto Paint/FD
3 Commercial Vehicle Rust/Paint Remover Epoxy primer, PU Primer SVE PU Auto Paint SVE FD Paint
4 Bus Coating Rust/Paint Remover NC primer SVE PU Auto Paint SVE PU Auto Paint/SVE PU Clear
5 Railway Coating Rust/Paint Remover Enamel primer, epoxy primer, enamel primer Top coat paint as per specification

SVE Hi – Gloss FD Automotive Paint

Car paint industries
  • SVE FD Auto Primer Surfacer is a synthetic surfacer, used as an undercoat surfacer in both Automotive and Industrial purposes.
  • This primer is suitable for all the automotive and industrial purposes as it protects the surfaces from corrosion and is also chemical resistant.
  • It is flexible and exhibits quick drying, excellent adhesion, good levelling and durability like properties.
Directions Of Use

Stir the contents thoroughly before use.

Mist Coat - (First Coat) Spray – Thin one part of paint by one part SVE T12 Thinner (by volume) . Stir well.

Apply a mist coat or thin coat at 2.5 to 3.5 Kg/cm2 (40-50 psi) and allow it to dry overnight. After drying, wet cut with 400 grade emery paper.

Full coat - (Second Coat) Spray- Reduce the viscosity of the paint to 18-20 seconds on Ford cup B4 with SVE T12 Thinner (30 parts of thinner to 100 parts of paint by volume) apply a single coat at 2.5 to 3.5 Kg/cm2 (40-50 psi) pressure.

For metallic Paints allow paint to dry for at least 96 hrs. Use any popular brand of rubbing compound, auto cleaner and wax polish.

Technical Details

Touch Dry Minutes – 20 Minutes

Finger Touch Dry Minutes – 2 hrs

Hard Dry Minutes – Overnight

Caution - This is not NC Lacquer. Contains aromatic hydrocarbons, mixture of isomers, may cause an allergic reaction

Pack - 500 ml, 1 Ltr, 4 Ltr, 20 Ltr

SVE Fast Drying paint is a durable, quick drying, high quality synthetic topcoat used for refinishing all types of two wheelers, Commercial vehicles and cars. It has excellent colour and gloss retention and gives a bright smooth finish.
For colour refer to Shade Card.

SVE Auto Nitrocellulose (NC) Paint

NC paints for metal, automotive
  • SVE NC Putty is a fine putty of good adhesion to iron steel and hard, sanded old coating.
  • It is a flexible to apply, fast drying, easy to sand and gives excellent adhesion on metals as well as over PU Primer.
  • It does not crack and spread ability.
  • It is ideal for use as fillers on automobile, two wheelers, bus bodies and various industrial decorative materials. It provides very soft and fine properties soon after its application.
Technical Details
  • Drying Time
  • Surface Dry- 5 Minutes @30°C
  • Sand able dry – 2 hrs @ 30°C
  • Hard Dry – Overnight
  • Application Method – Putty Knife
  • Colour - Grey

Pack - 1 kg

SVE Auto NC Surfacer is a synthetic surfacer, used as an undercoat surfacer in both Automotive and Industrial purposes.
This primer is suitable for all the automotive and industrial purposes as it protects the surfaces from corrosion and is also chemical resistance. It is flexible, exhibits quick drying, excellent adhesion, good levelling, good flowing, high coverage and high durable like properties.

Technical Details

Drying Time

  • Surface Dry - 10 Minutes@30°C
  • Sand able Dry - 2 Hrs @ 30°C
  • Hard Dry - Overnight
  • Application - Spray Gun
  • Dilution Ratio - Primer Surfacer to T11 thinner 1:1.5
  • SVE Auto NC Primer surfacer (LPS) – White/ Grey
  • SVE Auto NC Primer surfacer Red Oxide/Black

Pack - 500 ml, 1 Ltr, 4 Ltr, 20 Ltr

SVE NC Auto topcoats/undercoats finishes and are recommended as cost effective quality Paints in auto refinish segment. The specialised modified combination of rich solvents which helps diminishing paints to desired thickness.

  • It exhibits various properties like flexible, smooth surface, fast drying, excellent scratch hardness, excellent for refinishing, and many more.
  • Protecting paints from getting decayed
  • Used for automotive
  • Regulates the smoothness and accelerates the flow.
  • For Variety Refer to Shade Card for NC clear /Mat, Non Metallic & Metallic NC Paint.
Technical Details

Drying Time

  • Surface Dry 10 Minutes@ 30°C
  • Finger touch dry 60 minutes @ 30°C
  • Hard dry – Overnight
  • Dilution Ratio - NC Auto Paint to T11 Thinner ratio by volume - 1: 1.5
  • Application mode - Spray Gun
  • Colour – Refer to Shade cards
Directions Of Use
  • Mix NC auto Paint and Thinner @ ratio of 1:1.5
  • Apply 3 to 4 coats with 2 hrs gap.
  • After complete drying, buffing will enhance gloss. Buffing not recommended for Mat

Points to note - Shake well before use and do not over dilute. Strain the material through a fine sieve before use.

Note - Relative humidity should not exceed 75% .At higher humidity NC Paint can appear to be whitish due to excessive quick evaporation.

Pack - 500 ml, 1 Ltr, 4 Ltr, 20 Ltr

SVE PU Automotive Paints

SVE PU Paints
  • SVE PU Primer Surfacer is polyurethane based two component surfacer, used as an undercoat surfacer in both Automotive and Industrial purposes.
  • This primer is suitable for all the automotive and industrial purposes as it protects the surfaces from corrosion and is also chemical resistance.
  • It is Corrosion & Chemical resistant, flexible exhibits quick drying, excellent adhesion, good levelling, high covering, sagging & wrinkle free and durability like properties.
Directions for use
  • Mixing ratio - Base: Hardner (9:1)
  • Dilution ratio - 23-30% SVE T10 Thinner
  • Application - Spray
  • Color – White/Grey
Technical Details

Drying Time

  • Surface Dry 15-20 minutes @30°C
  • Finger Touch Dry - 2 Hrs
  • Hard Dry – Overnight
  • High gloss retention and excellent adhesion and long life flexible are the PU Paints properties, which includes top quality Polyutherane based high gloss finish used in automotive refinish and OEM segment. It is mixture of two components which mixed in some required ratio in order to the best results.
  • Its excellent UV resistance/light fastness, tough chemical resistance non-yellowing & smoothing surface, quick drying & easy tinting are some of the traits which makes in unique in various aspects
  • Excellent Adhesion and long life and is flexible and high covering
Directions For Use
  • Mixing Ratio - Base: Hardner (4:1)
  • Dilution ratio - 23 -30% SVE T10 thinner
  • Pot Life - 5-6 Hrs
  • Application - Spray
  • Color - Refer SVE Shade Card
Technical Details
  • Drying Time - Touch dry - 20 minutes
  • Finger Touch Dry – 2 hrs
  • Hard Dry Minutes - Overnight

Pack - 1 Ltr, 4 Ltr, 20 Ltr

SVE Metallic Base Coat

  • SVE Binder-mixed metallic base coats are used to give automobile a metallic finish consists of tinter, metallic pigment and metallic binder.
  • SVE provides binder mixed basecoats to make different colors and to give a smooth and light fast finish followed by Polyurethane clear over it.
  • It has excellent intercoat adhesion, metallic flake orientation, UV Resistance ,long life and non–yellowing, quick drying properties
  • It gives smooth surface & easy tinting.
Direction For Use
  • Mixing Ratio - Base to Hardner (9:1)
  • Dilution Ratio - 20-30% SVE T10 Thinner
  • Recoating Time - 3 - 4 Hrs.
  • Application - Spray
  • Colour - Refer to SVE Shade Card
Technical Details
  • Drying Time - Surface Dry -15 to 20 minutes
  • Hard Dry - Overnight

Pack - 1 Ltr, 4 Ltr, 20 Ltr

SVE PU Top Coat Auto Clear

  • SVE PU Top Coat Auto clear gives Mirror like glossy finish and excellent adhesion. It’s a mixture of two coat components used as a top coat in automotive.
  • It is flexible and scratch free, with long life and non-yellowing components with UV resistance, high chemical resistance. The flow and levelling act as main traits of the PU Clear, maintaining surfaces for longer time.
Directions For Use
  • Mixing ratio: Base - Hardner (2:1)
  • Dilution Ratio - 20- 30% SVE T10 Thinner
  • Curing time - 36 hrs
  • Application - Spray
Technical Details
  • Drying Time
  • Surface Dry - 20 Minutes
  • Finger touch Dry – 2 Hrs
  • Hard Dry - Overnight

Pack - 1 Ltr, 4 Ltr, 20 Ltr

Precautions
  • Do not breath vapour
  • Avoid contact with skin and eyes
  • Use proper respiratory systems
  • Keep containers in a well ventilated cool and dry place.
  • In case of accident/discomfort, seek medical advice.
  • No smoking